21． 我們將盡力達成你的計劃，如有異常，會及時通知你。
We will try our best to complete your plan, if there are any complications, we will notify you
immediately.
22.這個產品的長度為330.12MM,寬度為78.96MM,高度為45MM.膠厚為2MM,重量為70.63g,試模注塑機型號為250噸,
膠料顏色為黑色,產品外表
??面曬紋處理,內表面為拋光.需要日期章、環保章、材料章.前后模用2344氮硬，斜頂和行位座用738H，以上模具
信息正確嗎？請確認！
"The length of this part is 330.12MM, Width is 78.96MM, height is 45MM, thickness is 2MM, weight is
70.63g, the injection machine is 250T,the material is black, the outside of the part has texture,
inner side needs polishing, and it also needs a date and recycle stamp,
the core&cavity is 2344 nitridng, the lifter and slider shelf is 728H. Please check the information
above!"
23． 現在到了吃午鈑的時間，我們下午再繼續好嗎？
It is time to have lunch, let's discuss this project later this afternoon?
24.和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動
(The undercut area interferes with the slide block and needs to be filled with material to help the
slider move smoothly.)
25. 加肉太多? ? (The thickness added is too thick.)
26. 加肉面積太大 (The thickening area is too wide.)
27.GATE位置移位 ( The gate position is moved.)
28. 滑塊拆的位置 (The split line of slide block or the area of slide.)
29. 此處有尖角，填充困難 (It is hard to fill this area due to the sharp feature.)
30. 此處鋼材太薄，強度不足而且不容易冷卻
(The strength of this area is too weak and it is hard to cool because the steel is too thin.)
31. 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷
(We avoid designing the semicircle of the cylinder on the slide block because it will be pulled
apart or cause drag marks.)
32. 此處做斜銷在作動時會削到成品肉厚
(The part will be damaged if we make the lifter in this area.)
33. 這個面是裝配面，不能加料
(This is a critical surface where we cannot add additional material.)
34. 此處料位太厚，會有縮水，建議減料改善
(Because of the shrinkage of the thickness, we suggest reducing some wall thickness to improve it.)
35. 此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受
"(Please confirm whether it is a critical surface or not. Also, confirm whether it is acceptable to
have a slide
split line if we have a slide in this area. )"
36. 此處有倒勾，能否減料，使公母?？科?，不做滑塊和斜銷
"(Please confirm whether we can reduce material to the area where we have an undercut as indicated
to have shut off
on cavity side. No slide block and lifter will be made. )"
37. 請盡快確認這種拆模方式和結構，否則會影響模期
(Please confirm the issues of Parting line, Gate position...Etc. as soon as possible; otherwise,
the lead-time will be extended.)
38. 此面是否有特殊要求，能否有頂針印
(Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.)
39. P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響
(There are sharp edges if we set the parting line here, It will reduce the tool life)
40. 加大拔模角，以便脫模順利? ?We suggest enlarging the draft angle to help release the tool.)
